Danfoss 5000
参数表
1.
恢复工厂设定:
- 按 ”MENU”
- 找到参数 620
- 按 ”CHANGE DATA”, 选择 INITIALIZE
- 按 ‘OK’
- 断开电源，等待电源灯熄灭
- 送电
2.
Program parameters in ‘Menu’:
Verify each change with ”OK”
102  马达功率 kW (见马达铭牌)
103  马达电压 V (见马达铭牌)
104  马达频率 Hz (见马达铭牌)
105  马达电流 A (见马达铭牌)
106  马达转速 rpm (见马达铭牌)
128  电机热保护。ETR TRIP 1
201  最小马达频率 Hz (见马达铭牌 – 60%)。杀菌机设为0
202  最高马达频率 in Hz。输出频率上限。 (见马达铭牌 + 10%至少)
205  最高马达频率参考值。与参数202一样,
207, 208  加减速时间。5.00 sec.
315  4.0 mA
323  继电器输出。VLT 运转
- 按 ”DISPLAY STATUS”
当地启动/停止
用于检查马达转向
1.按 ”MENU”
2.按 STOP/RESET (显示开始闪烁)
3.将002更改为 LOCAL
4.按START启动马达, 按STOP/RESET停机
5.将002更改为REMOTE
6.按START 显示回复为平光)
自动调谐
条件：参数设定已完成，转向正确
1.Press STOP/RESET (display start flashing)
2.Program parameter 002 = LOCAL
107 = ENABLE (RS,XS)
3.Start auto tuning by pressing START button
Auto tuning takes approxiamately 3 - 4 min.
4.When auto tuning is ready, the alarm lamp start flashing on frequency converter and the display show: AUTO MOTOR ADAPT OK
5.Press STOP/RESET to reset alarm.
6.Restore parameter 002 = REMOTE
7.Press START (display return to steady light)
参数设定
Operation & Display
Load & Motor
References & Limits
001ENGLISH100SPEED OPEN LOOP200132 Hz CLOCKWISE002
REMOTE101H-CONSTANT TORQUE201Min 马达频率003000.000102马达功率 in kW202Max 马达频率004SETUP 1103马达电压 in V203MIN - MAX005ACTIVE SETUP104马达频率 in Hz2040.000006NOCOPY105马达电流 in A205Max motor reference007UPLOAD ALL PARAM106Rated motor speed inRPM206LINEAR0081107ENABLE (RS,XS)2075.00 s009FREQUENCY [Hz]108depends on the unit2085.00 s010REFERENCE [%]109depends on the unit209depends on the unit011马达电流 [A]110100%210depends on the unit012POWER [kW]1111.0 Hz211depends on the unit013LCP+DIG CTRL/ AS P100112not used212depends on the unit014DISABLE113100%21310.0 Hz015DISABLE114100%
214SUM016DISABLE115100%2150.00%017ENABLE1160.50 s2160.00%018LOCKED117100%217
0.00%019LOCAL=STOP1185 ms2180.00%1190.0 sec.2190.00%1200.0 sec.220notused121COAST/DELAY TIME221160%122COAST222160%1230.0 Hz2230.0 A12450%224
IVLT,MAX12550%2250.0 Hz12610.0 sec.226132.0 Hz1270.0 Hz (OFF)227-4000.000128ETR TRIP 1228
4000.000129NO2290 (OFF)%1300.0 Hz2300.0 Hz1310.0 Volt2310.0 Hz2320.0 Hz2330.0 Hz(Cont’d)
Inputs & OutputsSpecial functionsSerial communication300RESET400OFF5001301FREEZEREFERENCE401depends on the unit5019600 BAUD
302START402depends on the unit502LOGIC OR303REVERSING403ON503LOGIC OR304COAST INVERSE404OFF504LOGIC OR305JOGGING405MANUAL RESET
505LOGIC OR306SETUP MSB/SPEED UP4065 sec.506LOGIC OR307SETUP LSB/SPEED DOWN
407NO FUNCTION507LOGIC OR308REFERENCE408DISABLE508LOGIC OR3090.0 Volt409OFF
50910.0 Hz31010.0 Volt410depends on the unit51010.0 Hz311NO OPERATION411depends on the unit
511not used3120.0 Volt412DISABLE512DANFOSS31310.0 Volt413ON5131 sec.314REFERENCE
4140.000514OFF3154.0 mA4151500.00031620.0 mA416%31710 sec.4170.015318OFF4188 ms319
0-IMAX = 0-20 mA41930 ms3205000 Hz4205.03210-FMAX = 0-20 mA42110 ms3225000 Hz422
20.0 Volt323VLT RUNNING423parameter 1033240.00 sec.424parameter 1043250.00 sec.425parameter 103326UNIT READY/REM CTRL426parameter 1043275000 Hz427parameter 10332825000 Hz428
parameter 1043291024429parameter 103430parameter 104431parameter 103432parameter 104433100%4340.02 sec.435not used436not used437NORMAL438ENABLE439parameter 201
4400.014419999.99 sec. (OFF4420.00 sec. (OFF)4435.04440.01445DISABLE446AUTOMATIC
4470%4481.0004490.00%Technical functions618DO NOT RESET619DO NOT RESET620NORMAL OPERATION
Note:
 Parameter settings in bold italic are specific for TA FlexD. All other parameter settings are the factory settings from the manufacturer of the frequency converter (Software version: 3.0x).
 For the setting of parameter 102, 103, 104, 105 and 106, 见马达铭牌.
 Record all parameters changed from factory settings settings in test protocol.
 Sett following parameters after ready test / commissioning: Parameter 7 to UPLOAD (save settings in display EEPROM) Parameter 14 to DISABLE (disable STOP-button on frequency converter display) Parameter 18 to LOCKED (disable parameter changes from display)
 Save parameter settings to PC by VLT Dialog software program after test / commissioning.