http://s3/mw690/002cU7Rjgy6Hc5tb1Vo42&690

   首先校对塞规建立被校对环规http://img.iknow.bdimg.com/question/word/stop.png



校对塞规http://img.iknow.bdimg.com/question/word/de.png表面



校对规http://img.iknow.bdimg.com/question/word/de.png直线度寿命

1.彻底清洗环规与校对塞规http://img.iknow.bdimg.com/question/word/stop.png



2.用带清油http://img.iknow.bdimg.com/question/word/de.png胶片润滑校对塞规



3.反时针拧松锁紧螺钉



4.顺时针调节螺钉使环规开口并使径比校对塞规http://img.iknow.bdimg.com/question/word/de.png大



5.旋转环规进入塞规部（全形齿部分）使塞规http://img.iknow.bdimg.com/question/word/de.png大约牙留外面（使整塞规螺纹长度有教标准http://img.iknow.bdimg.com/question/word/de.png磨损）

6.反向旋转调节螺钉直塞环规间有轻轻http://img.iknow.bdimg.com/question/word/de.png拉动



7.反向旋转锁紧螺钉拧紧锁定调节螺钉并固定环规尺寸现应看塞环规间有见http://img.iknow.bdimg.com/question/word/de.png拉动步骤＃7和＃8能要重复多次取得合适http://img.iknow.bdimg.com/question/word/de.png拉动配合



环规从全形齿部分旋前端修正齿部分拉紧力应两部分间基本样才能保证牙形角正确http://img.iknow.bdimg.com/question/word/de.png



9.移走校对塞规

10.现环规旋入校对塞规前端1－1/22牙时会发现即使样短http://img.iknow.bdimg.com/question/word/de.png旋入也会有些阻力或拉力检验否锥度或喇叭口请环规放工作台上用校对塞规轻摇看其松紧度请非常小心要伤牙口



11.记住旋入1－1/22牙时http://img.iknow.bdimg.com/question/word/de.png感觉并让环规继续修正齿形部分前行种阻力应基本致虽由于更多http://img.iknow.bdimg.com/question/word/de.png齿面接触会使阻力略有增加



12.移下环规http://img.iknow.bdimg.com/question/word/comma.png重复步骤＃10和＃11



13.配合度应两面基本相同确保环规http://img.iknow.bdimg.com/question/word/de.png直线度

记住校对塞规尺寸做小了或前端磨损了能会错误http://img.iknow.bdimg.com/question/word/de.png指示环规有锥度或喇叭口校对塞规必须有精确http://img.iknow.bdimg.com/question/word/de.png直线度

 14.螺纹环规http://img.iknow.bdimg.com/question/word/de.png小径通常光滑通止规检验通常环规小径上下限按X级或XX级公差制造光滑塞规公 差

http://img.iknow.bdimg.com/question/word/dan.png方便使用者快速判断





尚没有标准http://img.iknow.bdimg.com/question/word/de.png拉力扭距值http://img.iknow.bdimg.com/question/word/de.png规范仍有些通用http://img.iknow.bdimg.com/question/word/de.png判断方法小规格规阻力应小于大规格http://img.iknow.bdimg.com/question/word/de.png轻松打转显太松了太紧则会伤害环规和校对规或造成们http://img.iknow.bdimg.com/question/word/de.png过度磨损良好质量http://img.iknow.bdimg.com/question/word/de.png规螺纹均经过精密研磨所尺寸变化小致使阻力产生明显同同W级公差http://img.iknow.bdimg.com/question/word/de.png两校对规能用同环规上感觉能完全同（能太紧另能太松）

另外由于径http://img.iknow.bdimg.com/question/word/de.png变化也能全部旋入与部分旋入时阻力会略有同大家要指望绝对http://img.iknow.bdimg.com/question/word/de.png完美合理范围内些同并要紧因环规与校对塞规此时仍好http://img.iknow.bdimg.com/question/word/de.png公差内



 由校对塞规设定由于公差http://img.iknow.bdimg.com/question/word/de.png原因并需要必须适配另校对塞规

当环规与校对塞规被订购时们必须工厂发货前调好有时客户http://img.iknow.bdimg.com/question/word/de.png校对塞规从制造商租借http://img.iknow.bdimg.com/question/word/de.png原配塞规