* Certificate

We certify that Gezfeel watch detailed on the enclosed certificate of guarantee is guaranteed against defects in material or workmanship for one year from the date of purchase, providing it has been sold by an appointed Gezfeel dealer. Within this period, regulation, adjustment, repair or replacement of parts or movement will be performed without charge except in the case of damage caused by accidents or lack of care. To take advantage of this guarantee, please present your watch together with a valid certificate of Guarantee to the appointed Gezfeel dealer from whom the watch was purchased or any member of the Gezfeel service network. You will need to pay for postage insurance and shipping, if required.

PLEASE NOTE THE FOLLOWING IMPORTNAT POINTS:

1. YOU MAY HAVE ADDITIONAL LEGAL RIGHTS, THIS GUARANTEE IS IN ADDITION TO, AND DOSE NOT AFFECT YOUR LEGAL RIGHTS.

2. THIS GURANTEE COVERS THE WATCH CASE, MOVEMENT, DIAL AND HANDS AND ANY METAL BRACELET, IT DOES NOT COVER THE GLASS, BATTERY, OR BRACELETS MADE OF A METERAIL OTHER THAN METAL OR SCRATCHES CAUSED BY NORMAL USE, SIMILARLY DAMAGE CAUSED BY NATURAL DISASTERS SUCH AS ERATHQUAKES OR FLOODS IS NOT COVERED.

3. MANY GEZFEEL WATCH ARE WATER RESISTANT. IF YOUR WATCH CARRIES THE DESIGNATION “WATER RESISTANT” OTHE CASE BACK OR DIAL, THIS GUARANTEE COVERS WATER DAMAGE.

4. TO TAKE ADVANTAGE OF THIS GUARANTEE, YOU EED TO PRSENT THE GUARNATEE CERTIFICATE AND COUPON, PROPERLY FILLED IN AND DATED BY THE APPOINTED GEZFEEL DEALER FROM WHOM THE WATCH WAS PURCHASED.

5. OUR GEZFEEL SERVICE NETWORK IS AT YOUR DISPOSAL, TO HELP YOU CARE FOR YOUR WATCH DURING AND AFTER THE PERIOD COVERED BY THIS GUARANTEE. HOWEVER, IF DURING THE GUARANTEE PERIOD ANYONE OTHER THAN A MEMBER OF OUR SERVICE NETWORK TEMPERS WITH OR INADVERTENTLY DAMAGES YOUR WATCH, WE RESERVE THE RIGHT TO RELINQUISH ALL RESPONSIBILIT UNDER THIS GUARANTEE.

6. WE WILL NOT HONOUR CERTIFICATES OF GUARANATEE THAT HAVE BEEN TAMPERED WITH OR ALTERED, NOR PHOTOCOPIES OF THESE CERTIFICATES PLEASE SUBMIT THE ORIGINAL.

 

INSTRUCTIONS FOR ANALOGUE QUARTA AND MECHANICAL WATCHES

Your watch is one of the following six type of analogue quartz and mechanical watches. Before using your new watch, please read the instructions pertaining to your watch type, they will help you to get the best out of the watch.

A. Two hands without calendar 

B. Two hands with date calendar

C. Two hands with day and date calendar

D. There hands without calendar

E. Three hands with date calendar

F. Three hands with day and date calendar

* Some models have a crew down crown instead of standard crown

How to unlock the crown

Unscrew the crown by turning it counterclockwise. Then, pull it out for time/calendar setting.

How to lock the crown

Push the crown back to the normal position. Then, turn it clockwise while pressing it until it locks in place.

When using the watch in water

Before using the watch in water, make sure the crown is screwed in completely, do not operate the crown when the watch is wet or in water.

 

How to start a mechanical watch?

To initially start your mechanical watch, swing it from side to side in a horizontal for about 30 seconds.

You can also be started by winding the crown.

NOTE: If the watch is worn daily, Gezfeel’s automatic mechanism will wind then main spring automatically through normal wrist movements.

 

HOW TO USE THE WATCH

Set the time/calendar following the instruction pertaining to your watch type.

TIME SETTING FOR MODELS WITHOUT CALENDAR

A D

1, Pull our the crown all the way.

2, Adjust the time by turning the crown in the desired direction.

3, Push the crown back into the normal position.

  NOTE: when setting the minute hand of a quartz watch, advance it to a few minutes a head of the time and then turn it back to the exact time.

 

TIME/CALENDAR SETTING FOR MODLES WITH CALENDAR

The date will change gradually between 9:00 PM and 4:00 AM (see note 1 on calendar setting)

For some models, however, it will change instantly when the hand pass the 12 O’clock maker at midnight.

 

FOR MODLES WITH DATE CALENDAR

B E

1, Pull out the crown to the 1^st click.

2, Turn the crown until the previous day’s date appears in the calendar frame.

3, Pull out the crown to the second click, and advance the hour and minute hands until the desired date appears.

 * If your watch has three has three hands, pull out the crown when the second hand is pointing to 12 o’clock.

4, Adjust the time by turning the crown in the desired direction.

5, Push the crown back into the normal position.

 

FOR MODEL WITH DAY AND DATE CALENDAR

C F

1, Pull out the crown to the first click.

2, Turn the crown until the previous day’s date appears in the calendar frame.

3, Turn the crown in the opposite direction until the desired language (bilingual) for the day before the desired day appears in the calendar frame.

4, Pull out the crown to the second click and advance the hour and minute hands until the desired date and day appears.

 * If your watch has three hands, pull our the crown when the second hands in pointing to 12 o’clock.

5, Adjust the time by turning the crown in the desired direction.

6, Push the crown back into the normal position.

 * If your watch has three hands, push the crown back in to the normal position in accordance with a time signal for “OO” seconds.

 

Notes on calendar setting:

1, Do not change the calendar between 9:00 PM and 4:00 AM, as it may not change properly. If it is necessary to set the calendar during that time period, first change the the time to any time outside those hours, set the calendar and then reset the correct time.

2, When the day shifts automatically to the next day, the other language will temporarily appear.

3, When setting the hour, check that AM/PM is correctly set, the watch is so designed that then calendar change once every 24 hours.

Turn the hands past the 12 o’clock marker to determine whether the time is set for the AM or PM period. If the calendar changes, the time is set for the AM period. If it dose not change, the time is set for the PM period.

 

CHANGING BATTERY IN ANALOGUE QUARTZ WATCH

Because the battery is inserted at the factory to check the function and performance of the watch, its actual service life once in your possession, may be less than the specified period. When the battery expires, make sure to replace it as soon as possible to prevent any malfunction. For battery replacement, we recommend that you contact an AUTHORIZED Gezfee DEALER and request they only use a genuine JAPAN OR SWISS battery.

 

Bettery life indicator

If your analogue quartz watch has a second hand, the battery needs to be replaced when you see the second moving in two-second increments in stead of the normal one-second increments (some calibers do not have this function.)

The watch will, however, remain accurate while the second hand is moving in two-second increments.

SPECIAL OPERATING INSTRUCTIONS FOR LADY MECHANICAL WAHTCHES CALIBRE NO: 6T51

A: Display

ATTACHED SCHEMATIC PLOT

*Date-et-day position may-be located at different position depends on models.

B: Winding the mainspring

To initially start your mechanical watch, swing it from side to side in a horizontal are for about 30 seconds.

These watched can also be started by winding the crown.

C: Setting the time

1, Pull the crown out to the first position.

2, Turn the crown to set hour and minute hands.

3, Push the crown back to the normal position.

D) Setting the date

1, Pull the crown out to the 1^st position.

2, Pull the crown from the 1^st position to the 2^nd position, then date advances one day.

3, After the date has been set, push the crown back to the normal position.

E) Setting the day of the week

1, Pull the crown out the 1^st position.

2, Turn the crown to the set the day of the week.

 If the day of the week is set between the hours of around 9:00PM and 4:00 AM, the day of the week may not change on the following day.

3, After the day of the week has been set, push the crown back to the normal position.

CHRONOGRAPH WATCHES OPERATING INSTRUCTIONS

Displays and Buttons

A) Setting the time

1, Pull the crown out to the 2^nd click position.

2, Turn the crown to set hour and minute hands.

3, After the time has been set, push the crown back to the normal position.

B) Setting the date

1, Pull the crown out to the 1^st click position.

2, Turn the crown anti-clock wise to set the date.

 *If the date is set between the hours of around 9:00 PM and 1:00 AM, the date may not change on the following day.

3. After the date has been set, push the crown back to the normal position.

C) Setting the day

1, Pull the crown out to the 1^st click position.

2, Turn the crown clockwise to set the day.

* If the day is set between the hours around 11:15PM and 6:00 AM, the day may not change on the following day.

3. After the date has been set, push the crown back to the normal position.

USING THE CHRONOGRAPH

This chronograph is able to measure the display time in 1/1 second united up to maximum 11 hours, 59 minutes and 59 seconds.

[Measuring time with the chronograph]

1, Press button “A” to start the chronograph

2, The chronograph can be started and stopped each time button “A” is pressed.

3, Pressing button “B” resets the chronograph and chronograph hands return to their zero positions.

 

CHRONOGRAPH RESET

This procedure should be performed when the chronograph second hand dose not return to zero position.

1, Pull the crown out to the 2^nd click position.

2, Press the button “A” once to set the chronograph second hand to the zero position.

*The chronograph hour and minutes hands are synchronized with chronograph second hand.

*The chronograph second hand can be advanced on scale by pressing button “A” once.

*The chronograph second hand can be advanced rapidly by continuously pressing button “A”

3, Once the hands been zeroed, reset the time and return to the crown to its normal position.

* Do not return crown to normal position while chronograph second hand return to 12:00 position.

Hand stops on the way when crown are returned to normal position and these positions are recognized as 12:00(zero) position.

ANOTHER CHRONOGRAPH WATCHES OPERATING INSTRUCTIONS IS THE SAME AS ABOVE.

TO PRESERVE THE QUALITY OF YOUR WATCH

WATER RESISTANCE

*Non-water resistance

If“WATER RESISTANT” is not inscribed on the case back, your watch is not water resistant, and care should be taken not to get it wet as water may damage the movement. If the watch becomes wet, we suggest that you have it checked by an AUTHORIZED DEALER or SERVICE CENTER.

*Water resistance(5 bar)

If “WATER RESISTANT 3 BAR” is inscribed on the case back, your watch is designed and manufactured to withstand up to 3 bar and is suitable for wearing while swimming, yachting and taking a shower.

*Water resistance (10 bar/15bar/20bar)

If “WATER RESISTANT 10 BAR”, “WATER RESISTANT 15 BAR”, or “WATER RESISTANT 20 BAR” is inscribed on the case back, your watch is designed and manufactured to withstand up to 10 bar/15 bar/ 20 bar, respectively, and is suitable for wearing while taking a bath or shallow diving, but not for scuba diving. We recommend that you wear a Diver’s watch while scuba diving.

* Before using a water resistant 5, 10, 15 or 20 bar watch in water, make sure the crown is pushed in completely.

Do not operate the crown when the watch is wet or in water. If used in sea water, rinse the watch in fresh water and dry it completely.

* When taking a shower while wearing a water resistant 5 bar watch, or taking a bath while wearing a water resistant 10, 15, or 20 bar watch, make sure to observe the following: Do not operate the crown when the watch is wet with soapy water or shampoo.

* If the watch is left in warm water a slight time loss or gain may be caused. This condition, however, will be corrected when the watch returns to normal temperature.

NOTE:

Pressure in bar is a test pressure and should not be considered as corresponding to an actual diving depth since swimming movements tend to increase the pressure at a given depth. Care should also be taken when wearing and diving into water.

TEMPERATURE RANCE

(for analogue quartz watches only)

Your watch works with stable accuracy in a temperature range of 5 and 35 (40 and 95).

Temperatures over 60 or 140 (50 or 122 for some calibres) may cause battery leakage or shorten the battery life.

Do not leave your watch in very low temperatures below -10 or + 14(-5 or +24 for some calibres) for a long time since the cold may cause a slight time loss or gain.

However, the above condition will be corrected when the watch returns to normal temperature.

SHOCKS&VIBRATION

General light activities will not affect your watch, but be careful not to drop your watch hit it against hard surfaces, as this may cause damage.

MAGNETISM

The watch will be adversely affected by strong magnetism. Keep the watch away from close contact with magnetic objects. (In the case of quartz watch, normal accuracy will return if the watch is moved away form the magnetic filed.)

PERIODIC CHECK

It is recommended that the watch be checked once every 2-3 years. Have your watch checked by an AUTHORIZED DEALER or SERVICE CENTER to ensure that the case, crown, gasket and crystal seal remain intact.

CARE OF CASE AND BRACELET

To prevent possible rusting of the case and bracelet caused by dust, moisture and perspiration, wipe the periodically with a soft dry cloth.

CHEMICALS

Be careful not to expose the watch to solvents (e.g., alcohol and gasoline), mercury (e.g., from a broken thermometer), cosmetic sprays, detergents, adhesives or paints, as the case, bracelet, etc. may become discolored deteriorate or damaged.

PRECAUTIOIN REGARDING CASE BACK PROTECTIVE FILM

If your watch has a protective film and/or a sticker on the case back, make sure to peel them off before using your watch. Otherwise, perspiration getting under them may rust the case back.